Qucs File Formats¶
This document describes the schematic and library file formats of Qucs.
Schematic file format¶
This format is used for schematics (usually with suffix .sch
) and for data
displays (usually with suffix .dpl
). The following text shows a short
example of a schematic file.
<Qucs Schematic 0.0.6>
<Properties>
<View=0,0,800,800,1,0,0>
</Properties>
<Symbol>
<.ID -20 14 SUB>
</Symbol>
<Components>
<R R1 1 180 150 15 -26 0 1 "50 Ohm" 1 "26.85" 0 "european" 0>
<GND * 1 180 180 0 0 0 0>
</Components>
<Wires>
<180 100 180 120 "" 0 0 0 "">
<120 100 180 100 "Input" 170 70 21 "">
</Wires>
<Diagrams>
<Polar 300 250 200 200 1 #c0c0c0 1 00 1 0 1 1 1 0 5 15 1 0 1 1 315 0 225 "" "" "">
<"acnoise2:S[2,1]" #0000ff 0 3 0 0 0>
<Mkr 6e+09 118 -195 3 0 0>
</Polar>
</Diagrams>
<Paintings>
<Arrow 210 320 50 -100 20 8 #000000 0 1>
</Paintings>
В файле несколько разделов. Все они объясняются ниже. Каждая линия состоит из не более чем одного информационного блока, начинающегося знаком меньше
(<
) и заканчивающегося знаком больше
(>
).
Properties¶
Первый раздел начинается с <Properties>
и заканчивается </Properties>
. Он содержит свойства документа, находящегося в файле. Каждая строка необязательна. Поддерживаются следующие свойства:
<View=x1,y1,x2,y2,scale,xpos,ypos>
содержит положение в пикселах окна схемы (первые четыре числа), его текущий масштаб и текущее положение верхнего левого угла (два последних числа).<Grid=x,y,on>
содержит шаг сетки в пикселах (первые два числа) и включена сетка (последнее число = 1) или выключена (последнее число = 0).<DataSet=name.dat>
содержит имя файла набора данных, связанного с этой схемой.<DataDisplay=name.dpl>
содержит имя файла со страницей просмотра данных, связанной с этой схемой (или имя схемного файла, если этот документ является просмотром данных).<OpenDisplay=yes>
содержит 1, если страница показа данных открывается автоматически после моделирования, в противном случае - 0.<Script=name.m>
contains the file name of the octave script associated with this schematic.<RunScript=0>
contains 1 if the octave script is executed after the simulation.<showFrame=0>
specify if a frame is drawn and if so which size it is. valid values are 0 (do not show a frame), 1 (A5 landscape), 2 (A5 portrait), 3 (A4 landscape), 4 (A4 portrait), 5 (A3 landscape), 6 (A3 portrait), 7 (letter landscape) and 8 (letter portrait).<FrameText0=NE555 sub-circuit model>
,FrameText1=Draw by: anonymous
,FrameText2=Date: 1984
, and<FrameText3=Revision: 42>
specifiy the texts to be placed into the frame text boxes.
Symbol¶
Этот раздел начинается с <Symbol>
и заканчивается </Symbol>
. Он содержит элементы рисования, составляющие схемное обозначение для файла. Это обычно используется только для схемных файлов, которые считаются подсхемой.
Refers to “Symbol definition” in the “Shared file format” section at the end of this document.
Components¶
Этот раздел начинается с <Components>
и заканчивается </Components>
. Он содержит компоненты цепей схемы. Формат строки:
<type name active x y xtext ytext mirrorX rotate "Value1" visible "Value2" visible ...>
type
(“тип”) означает компонент, например,R
для резистора,C
для конденсатора.name
(“имя”) - уникальное обозначение компонента на схеме, например,R1
для первого резистора.1
в полеactive
(“активный”) показывает, что этот компонент активный, то есть используется в моделировании.0
показывает, что он неактивный.- Следующие два числа являются x и y координатами центра компонента.
- Следующие два числа являются x и y координатами верхнего левого угла текста компонента. Они отсчитываются от центра компонента.
- Следующие два числа указывают на зеркальное отображение относительно оси x (
1
- зеркальное отображение,0
- нет зеркального отображения) и вращение против часовой стрелки (кратно 90 градусам, то есть 0...3). - Следующие параметры являются значениями свойств компонента (в кавычках), за которыми следует
1
, если это свойство видимо на схеме (в противном случае0
).
Wires¶
Этот раздел начинается с <Wires>
и заканчивается </Wires>
. Он содержит проводники (электрическое соединение между компонентами цепи), их метки и узлы. Формат строки:
<x1 y1 x2 y2 "label" xlabel ylabel dlabel "node set">
- Первые четыре числа являются координаиами проводника в пикселах: x-координата начальной точки, y-координата начальной точкиt, x-координата конечной точки и y-координата конечной точки. Все проводники должны быть либо горизонтальными (обе x-координаты равны), либо вертикальными (обе y-координаты равны).
- Первая строка в кавычках - имя метки. Она пустая, если пользователь не установил метку на этот проводник.
- Следующие два числа - x- и y-координаты метки или ноль, если метки не существует.
- The next number is the distance between the wire starting point and the point where the label is set on the wire.
- Последняя строка в кавычках - параметры цепи проводника, то есть начальное напряжение узла, используемое ядром симулятора для поиска решения. Эта строка пустая, если пользователь не установил параметры узла цепи для этого проводника.
Diagrams¶
Этот раздел начинается с <Diagrams>
и заканчивается </Diagrams>
. Он содержит диаграммы с их графиками и маркерами.” The line format is as follows (line break not allowed):
<diatype x y width height grid gridcolor gridstyle log xAutoscale xmin
xstep xmax yAutoscale ymin ystep ymax zAutoscale zmin zstep zmax
xrotate yrotate zrotate "xlabel" "ylabel" "zlabel" "[freq Hz;]*">
<"graphvar" color thickness precision numberformat style axisside>
<Mkr x y precision numberformat transparent>
</diatype>
Diagram line format:
- The
diatype
token specifies the type of diagram. - The
x
andy
numbers are the coordinate of lower left corner. - The
width
andheight
numbers of diagram boundings. - The
grid
flags with 1 if grid is on and 0 if grid is off. - The
gridColor
in 24 bit hexadecimal RGB value, e.g. #FF0000 is red. - The
gridstyle
is the line style sued of the grid. - The
log
has two field to flag which axes have logarithmical scale. - The
xAutoscale
,xmin
,xstep
,xmax
configure the x-axis scaling, limits. - The
yAutoscale
,ymin
,ystep
,ymax
configure the y-axis scaling, limits. - The
zAutoscale
,zmin
,zstep
,zmax
configure the z-axis scaling, limits. - The
xrotate
,yrotate
,zrotate
numbers set the 3D rotation. - The
xlabel
,ylabel
,zlabel
hold the labels used on each axis. - The list of frequencies
"[freq Hz;]*"
is used byPhasor
andWaveac
.
Here is a list of known diagram types:
Curve
for a locus curve diagram.Smith
for an impedance Smith diagram.ySmith
for an admittance Smith diagram.PS
for a mixed polar/smith diagram.SP
for a upper-half mixed polar/smith diagram.Polar
for a polar diagram.Rect
for a 2D-cartesian diagram.Rect3D
for a 3D-cartesain diagram.Tab
for a tabular diagram.Time
for a timing diagram.Truth
for a truth-table diagram.Phasor
for a complex phasor diagram.Waveac
for a wave as temporal diagram.
Graph line format:
- The
graphvar
specify the variable this graph is plotting for. - The
color
,thickness
andstyle
refers to the pen used to draw the curve. - The
precision
specify the number of digits used when displaying data values. - The
numberformat
is an integer that specify how the number are formated (0 for real/imag, 1 for polar/deg and 2 for polar/rad). - The
axisside
is an integer indicating on which side the Y axis should be placed ().
Marker line format:
- The
x
andy
are the location of the marker. - The
precision
... - The
numberformat
... - The
transparent
Paintings¶
Этот раздел начинается с <Paintings>
и заканчивается </Paintings>
. Он содержит элементы рисования, которые используются в схеме.
Refers to “Shared file format” section below.
Library file format¶
This format is used for libraries (usually with suffix .lib
). The
following text shows a short example of a library file.
<Qucs Library 0.0.14 "Ideal">
<DefaultSymbol>
<.ID -26 13 D>
<Line -30 0 60 0 #000080 2 1>
<Line -6 -9 0 18 #000080 2 1>
<Line 6 -9 0 18 #000080 2 1>
<Line -6 0 12 -9 #000080 2 1>
<Line -6 0 12 9 #000080 2 1>
<Line -6 9 4 0 #000080 2 1>
<.PortSym -30 0 1 0>
<.PortSym 30 0 2 180>
</DefaultSymbol>
<Component VSum>
<Description>
Voltage adder
</Description>
<Model>
.Def:Ideal_AP1 _net3 _net2 fc="1E3"
Sub:VSUB1 _net0 _net1 _net2 Type="VSub"
Sub:LP1F1 _net3 _net0 Type="LP1" fc="fc2" V0="0"
Sub:HP1F1 _net3 _net1 Type="HP1" fc="fc2"
Eqn:Eqn1 fc2="fc/0.6436" Export="yes"
.Def:End
</Model>
<ModelIncludes "HP1.sch.lst" "LP1.sch.lst" "VSub.sch.lst">
<Symbol>
<Ellipse -20 -20 40 40 #000080 2 1 #c0c0c0 1 0>
<Line -10 0 20 0 #000080 1 1>
<Line 0 -10 0 20 #000080 1 1>
<Line 0 30 0 -10 #000080 2 1>
<.PortSym 0 30 2 0>
<.PortSym 30 0 3 180>
<Line 20 0 10 0 #000080 2 1>
<.ID 10 14 VADD>
<Line 0 -20 0 -10 #000080 2 1>
<.PortSym 0 -30 1 0>
</Symbol>
</Component>
The first line specify that this file is a Qucs library file generated by Qucs 0.0.14 and that the library is named “Ideal”.
The file contains on optional DefaultSymbol
section, followed by
Component
sections. Each section is explained below.
Default symbol¶
This section starts with <DefaultSymbol>
and ends with </DefaultSymbol>
.
It contains painting elements creating a default schematic symbol for any
subsequent component declaration that doesn’t define its own.
Refers to “Shared file format” section below.
Component¶
This section starts with <Component>
and ends with </Component>
. It
contains the component definition for use with schematic documents.
The component section is an aggregation of the following sub-sections:
<Description>
and</Description>
contain lines of free text describing the component function.<Model>
and</Model>
contain the Qucsator netlist lines for this component.<ModelIncludes "value0" "value1" ...>
...<Spice>
and</Spice>`
are optional and contain the Spice netlist lines for this component.<Symbol>
and</Symbol>
are optional and contain painting elements defining the schematic symbol to be used with this component. Refers to “Symbol definition” section below.